Getting Familiar with Plumbing: A Must for Bathtub Installation
Getting Familiar with Plumbing: A Must for Bathtub Installation
Blog Article
We have encountered the article involving A Step-by-Step Guide to Installing a Bathtub listed below on the web and felt it made good sense to discuss it with you in this article.
Setting up a bathtub isn't precisely brain surgery, however it does need solid plumbing, carpentry, and often, tiling skills. Replacing an old bathtub with a new one is additionally a moderately tough project. If the old tub is readily available, the project can move immediately; if you have to open a wall to eliminate the old bathtub and place the brand-new tub, the job is a lot harder. In either case, the project is within a home handyman's abilities, although you will certainly require a helper to leave the old bathtub as well as set in the new one. Make sure you have certified yourself for the task and also are comfortable trying it. Rather than employing a contractor to take over a halfway-completed project, it is better to consider using one prior to you start. Possibilities are you may require a specialist plumber to make tube links.
This write-up will assist you set up a brand-new bath tub in your shower room if you have currently purchased a new bathtub as well as do not need to transform the arrangement of your previous water supply pipelines.
Your devices as well as product checklist must make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, then the first thing you must do is separate the water system. After doing so, turn on the faucets to drain any type of water continuing to be in the system. The procedure of eliminating the existing taps can be rather problematic due to the limited accessibility that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a cloth all set for the remaining water that will originate from the pipelines. Once the supply pipes have been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing substance.
Prior to carrying on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic connector to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin making sure that the washing machines remain in area in between the faucet as well as the sink. Secure the faucet in place with the supplier supplied backnut. As soon as the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type ought to be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bath tub in the required setting. The wood boards are useful in equally spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 small factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be attained by examining the level and adjusting the feet on the bath tub till the spirit level reads degree.
To install taps, fit all-time low of the furthest versatile tap adapter to the suitable supply pipeline by making a compression join; then do the very same for the various other tap.
Activate the water supply and also check all joints and also new pipework for leaks and also tighten them if needed. Load the bath tub as well as also check the overflow outlet and also the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the bath tub should wait till the tub has actually been used a minimum of once as this will settle it right into its last placement.
Planning for the Setup
First of all, the sustaining frame provided with the bathroom should be fitted (if called for) according to the maker's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the faucets device to avoid strain on the bath tub.
Fit the versatile tap ports to the bottom of both taps utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you utilize all of the provided washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to split an inflexible seal, creating the water to penetrate the wall in between the bath as well as the tiling, bring about complications with wetness and possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to blend in your fixtures and fittings. They are marketed in tubes and also cartridges, as well as are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of drenched paper or soft rope. Remember to always fill the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealant can split relatively early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently available on the market. It is a good idea to fit the ceramic tiles making use of waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our part on Tools You Need to Install a New Bathtub . Thanks a ton for spending some time to browse our piece of content. Don't hesitate to set aside a second to promote this blog if you enjoyed it. Thanks for going through it.
Call us now! Report this page